Tapered Roller Bearings — Quote the Cone and the Cup Together
A Bearing That Takes Two Loads at Once
A tapered roller bearing uses conical rollers and raceways whose apex lines all meet at one point on the bearing axis. That geometry gives true rolling along the roller length and lets the bearing carry a heavy radial load together with a large axial load — something a deep groove ball bearing can only do in limited measure. The inner ring with its rollers and cage (the cone) separates from the outer ring (the cup), which makes mounting and adjustment straightforward and lets a buyer order the two halves separately. The trade-off is that a single tapered roller bearing accepts axial load in one direction only, so they are usually fitted as an opposed pair whose clearance or preload is set at assembly. Getting the pair right is the difference between a hub that runs cool for years and one that seizes in a month.
Single, Paired or Four-Row
| Variant | Construction | Where it is used |
|---|---|---|
| Single row, separable cone and cup | One cone, one cup; axial load in one direction | Gearboxes, pump shafts, conveyor pulleys, agricultural axles |
| Matched pair, back-to-back (DB) | Two bearings opposed with contact lines diverging toward the axis | Wheel hubs, machine tool shafts, high moment stiffness |
| Matched pair, face-to-face (DF) | Two bearings opposed with contact lines converging toward the axis | Where some misalignment is expected and moment stiffness is less critical |
| Double row, one cup or two cups | Two roller rows in one assembly; axial load both directions | Wheel ends, crane sheaves, rolling mill and heavy industrial shafts |
| Flanged cup | Cup with an integral flange for axial location | Housings without a shoulder, light alloy housings |
| Four-row | Four rows for very heavy radial load | Rolling mill roll necks (state the duty cycle in the RFQ) |
Dimensions, Angle and Setting
Give bore (d), outside diameter (D) and the overall width (T), plus the cone width and cup width if the assembly is already split. Then give the contact angle or the dimension series, since a steeper angle carries more axial load and less radial load at the same envelope. State the radial and axial loads, the direction of the axial load and whether it reverses, the speed and the lubrication method. For a paired arrangement, tell us the arrangement (DB, DF or tandem) and the required setting — axial clearance or preload — because that value is set at assembly and cannot be corrected by buying a different bearing later. Include the shaft and housing fit tolerances, and say whether you need the cone and cup as a matched set with one lot number or as separate service parts. If you want the bearing supplied with a spacer or a setting shim, put it on the same RFQ. We buy matched pairs as one unit from the partner factory and keep the pair identity on the packing list and inspection record.
Where Tapered Rollers Are the Right Answer
Automotive wheel hubs and axle ends, manual and automatic gearboxes, differentials, industrial reducers and gear motors, machine tool spindles and workheads, conveyor pulleys and idlers, crane and hoist sheaves, rolling mill roll necks, agricultural implement hubs and gearboxes, wind turbine gearbox shafts, and pump and compressor shafts with a combined load. Wherever an axial load sits on the same shaft as a heavy radial load, a tapered roller pair is usually the first arrangement to check.
Replacing a Worn Cone, Cup or Pair
Because the cone and cup separate, a replacement enquiry is often for only one half. Measure the bore, outside diameter and overall width, and read any marking off both the cone and the cup — a cup from one assembly will not necessarily set correctly with a cone from another. Tell us which half failed and how: spalling on the roller large end points to insufficient axial setting, overheating to too much preload, and edge loading to misalignment. If the bearings were fitted as a pair, replace both halves together and state the original setting; mixing a new cone with a worn cup gives an unpredictable clearance. We match the dimensions and the roller form to the standard designation in our catalog and confirm d, D and T in the first reply. We do not list third-party brand names as our own products, and we state interchangeability only as a match of dimensions and construction, never as a claim of brand authorization.
Tapered Roller Bearing Models
Tapered Roller Bearing Questions
Can I order just the cone or just the cup?
Yes, if you are replacing a single service part and the mating half is still within tolerance. Send the marking and dimensions from both halves so we can confirm the pair geometry. If the original bearing ran as a matched pair, we recommend replacing both halves together.
What is the difference between back-to-back and face-to-face?
Back-to-back (DB) spreads the contact lines outward and gives higher moment stiffness, which is why wheel hubs and machine tool shafts normally use it. Face-to-face (DF) is more tolerant of housing misalignment but carries less moment. Tell us the arrangement in the RFQ and we will quote the pair as one unit.
How is the axial setting specified?
State the required axial clearance or preload, or the shim thickness used on the current assembly. The setting is made at assembly and is not a property you can change by choosing a different bearing later, so it belongs in the first message along with d, D and T.
Request a Quote for Tapered Roller Bearings
Send the bore, outside diameter, width and the duty in one RFQ. We confirm the fit before quoting and state MOQ, lead time and Incoterms.