Specialty Bearings — Five Families Built Around One Assembly

Bearings Defined by the Assembly, Not the Bore

A standard bearing is chosen from a catalogue by bore, outside diameter and width. These five families are chosen the other way round: the assembly around them decides the bearing. A wheel hub unit has to carry the flange, the wheel bolts and the ABS ring; an insulated bearing has to stop shaft current in a variable-frequency motor; a ball screw support bearing has to hold an axis to a few microns under reversing axial load; a rod end has to pivot while it pulls; an eccentric has to turn rotation into an adjustable offset. Because the housing, the mating part and the duty are part of the specification, we ask for the drawing or the assembly number before quoting — a bare dimension series is not enough to guarantee fit.

We source all five from audited partner factories and ship them with a dimensional inspection report and material certificate tied to the lot. Where a buyer needs a change to a flange, a coating or a thread, the modification is executed by the partner workshop and recorded on the inspection sheet, so the part that arrives matches the drawing rather than a near-enough substitute.

Wheel Hub Bearings

Back to top of this page

A wheel hub bearing unit is a pre-assembled, sealed and pre-adjusted cartridge that carries the wheel, locates the brake disc and reacts cornering loads. Instead of two separate tapered or ball bearings that a mechanic has to set by feel, the unit uses two rows of angular contact balls or tapered rollers in one housing with the internal clearance already fixed. Later generations add a mounting flange, wheel studs and a magnetic encoder ring for the ABS or wheel-speed sensor, so the bearing becomes a bolt-on chassis component rather than a spare part pressed into a hub. You will find them on passenger cars, light commercial vehicles, trailer axles and off-highway axle ends where a predictable service life matters more than rebuildability.

Selection starts with the vehicle or axle platform, not with a bore size. Send the flange bolt circle, the number and thread of the wheel studs, the offset, whether the unit is driven or non-driven, and whether an ABS encoder ring is needed and on which side the sensor reads. Give the drawing or the old assembly number if you have it, plus the left/right or front/rear position if the two sides differ. State the wheel load, the tyre radius and the duty — stop-start urban delivery, sustained motorway speed and agricultural field work ask for different grease and seal designs. Tell us the braking and corrosion environment too, because a unit exposed to road salt or washdown needs a different seal and coating. We quote the unit as one line item with the seal, encoder and flange already assembled, and we confirm the bolt pattern against your drawing before the order is placed.

Wheel hub unit, 5-bolt flange, 120 mm PCD, ABS ring — placeholder illustration

Wheel hub unit, 5-bolt flange, 120 mm PCD, ABS ring

  • Bolts5
  • PCD120 mm
  • EncoderABS ring
  • SealSealed
[PLACEHOLDER]
Wheel hub unit, 6-bolt flange, 139.7 mm PCD, driven — placeholder illustration

Wheel hub unit, 6-bolt flange, 139.7 mm PCD, driven

  • Bolts6
  • PCD139.7 mm
  • DriveDriven axle
  • EncoderABS ring
[PLACEHOLDER]
Wheel hub unit, 8-bolt flange, 165.1 mm PCD, trailer — placeholder illustration

Wheel hub unit, 8-bolt flange, 165.1 mm PCD, trailer

  • Bolts8
  • PCD165.1 mm
  • DriveNon-driven
  • DutyTrailer axle
[PLACEHOLDER]

Insulated Bearings

Back to top of this page

An insulated bearing is a standard bearing with an electrically insulating layer added to stop current from passing through the rolling contact. In a variable-frequency motor, a traction motor or a generator, capacitive and inductive shaft voltages can drive a current through the bearing; the resulting arcing pits the raceways, frosts the balls and destroys the grease within weeks. The usual fix is a ceramic oxide coating sprayed onto the outer or inner ring outer surface, or a hybrid design with ceramic rolling elements. Coated versions keep the load rating and dimensions of the steel bearing they are built from, which means an insulated unit can often replace a standard one without changing the housing.

The value that decides the specification is electrical, not dimensional. Tell us the resistance and the breakdown voltage you need, and whether the coating should be on the inner ring or the outer ring — the choice depends on where the current enters and on which ring is stationary in your assembly. Give the bore, outside diameter, width, the base bearing type and the required clearance and precision grade, then the cage material, seal arrangement and lubricant. State the supply voltage, whether the drive is a PWM inverter, the operating temperature and the humidity, since condensation lowers the effective insulation. Ask for the insulation test record with the lot if your QC needs it: we arrange the test at the partner factory and ship the report with the dimensional inspection record. If the duty also needs high speed or corrosion resistance, say so at the start — a hybrid bearing may be the better answer than a coated steel one, and we will quote both rather than leave you to guess.

Insulated deep groove ball bearing, 40 × 80 × 18 mm, outer-ring coating — placeholder illustration

Insulated deep groove ball bearing, 40 × 80 × 18 mm, outer-ring coating

  • Bore (d)40 mm
  • Outside diameter (D)80 mm
  • Width (B)18 mm
  • CoatingOuter ring
  • ClearanceC3
[PLACEHOLDER]
Insulated cylindrical roller bearing, 50 × 90 × 20 mm — placeholder illustration

Insulated cylindrical roller bearing, 50 × 90 × 20 mm

  • Bore (d)50 mm
  • Outside diameter (D)90 mm
  • Width (B)20 mm
  • TypeNU
  • CoatingOuter ring
[PLACEHOLDER]
Hybrid insulated ball bearing, 30 × 62 × 16 mm, sealed — placeholder illustration

Hybrid insulated ball bearing, 30 × 62 × 16 mm, sealed

  • Bore (d)30 mm
  • Outside diameter (D)62 mm
  • Width (B)16 mm
  • BallsCeramic
  • Seal2RS
[PLACEHOLDER]

Ball Screw Support Bearings

Back to top of this page

A ball screw support bearing holds the end of a screw where an axis has to reverse direction without losing position. It is normally a matched set of angular contact ball bearings with a steep contact angle — commonly 60 degrees — arranged back-to-back or in a duplex pair so the set takes axial load in both directions with very high stiffness. The fixed end uses the support bearing; the floating end uses a simple radial bearing that allows the screw to grow with temperature. This pairing is what separates a positioning axis that repeats within a few microns from one that drifts as the machine warms up. Typical installations are CNC machining centres, injection moulding machines, robot linear axes, semiconductor stages and precision measuring equipment.

Give us the screw shaft end drawing first: the journal diameter, the thread and nut details, the shoulder height and the available axial envelope. Then state the contact angle, the pair arrangement (DB, DF, DT or a duplex set), the preload class and the required axial stiffness — those three values decide both positioning accuracy and the heat the set generates at speed. Tell us the precision grade (P4 or P2 for precision axes), the maximum axial load in both directions, the rotational speed, the lubrication method and whether the set must be sealed. Include the housing bore tolerance and the clamping nut specification if they are fixed, because a support bearing loses its preload if the nut is under-torqued or the housing is out of round. We buy matched sets as one unit from the partner factory and keep the set identity on the packing list and inspection record, so the two halves that reach your bench belong together. If your axis also needs a floating-end bearing, put it on the same RFQ and we will quote the pair.

Ball screw support bearing set, 20 mm shaft, 60° — placeholder illustration

Ball screw support bearing set, 20 mm shaft, 60°

  • Journal20 mm
  • Contact angle60°
  • ArrangementDB pair
  • PreloadMedium
[PLACEHOLDER]
Ball screw support bearing set, 25 mm shaft, P4 — placeholder illustration

Ball screw support bearing set, 25 mm shaft, P4

  • Journal25 mm
  • Contact angle60°
  • PrecisionP4
  • PreloadLight
[PLACEHOLDER]
Ball screw support bearing set, 30 mm shaft, sealed — placeholder illustration

Ball screw support bearing set, 30 mm shaft, sealed

  • Journal30 mm
  • Contact angle60°
  • SealSealed
  • PreloadHeavy
[PLACEHOLDER]

Rod End Bearings

Back to top of this page

A rod end bearing — also called a heim joint or a spherical plain bearing with a shank — combines a spherical sliding contact with a threaded or welded stem. The inner ring can swivel inside the outer ring, so the joint transmits a pulling or pushing force while allowing angular movement between two links that are not perfectly in line. It is the normal choice for steering linkages, hydraulic cylinder eyes, gear and throttle linkages, agricultural implement arms, packaging machine cranks and any lever where a rigid pin joint would bind. Unlike a rolling bearing it is not designed for continuous rotation: it oscillates through a small angle, and its life is set by the sliding contact and its lubrication.

Specify the bore of the eye, the thread size and pitch on the shank, and the hand of the thread — right-hand and left-hand rod ends are used together on a turnbuckle-style link, and getting the hand wrong makes the link impossible to adjust. State whether the shank is male or female, whether it needs a grease nipple, and the required misalignment angle. The decisive material choice is the sliding contact: a steel-on-steel joint is re-lubricatable and handles shock and high temperature, while a PTFE-lined or maintenance-free version is better where grease would collect dirt or where the joint is hard to reach after assembly. Give the radial and axial static and dynamic loads, the direction of the load relative to the shank, the operating temperature and the environment, plus any corrosion requirement such as zinc plating or stainless construction. Send the linkage drawing if the ball width or the housing offset is constrained. We will confirm the thread hand and the eye bore on the quotation rather than assume a standard.

Rod end, 12 mm bore, M12×1.25 male, right-hand — placeholder illustration

Rod end, 12 mm bore, M12×1.25 male, right-hand

  • Eye bore12 mm
  • ThreadM12×1.25 male
  • HandRight-hand
  • ContactSteel-on-steel
[PLACEHOLDER]
Rod end, 16 mm bore, M16×1.5 female, left-hand — placeholder illustration

Rod end, 16 mm bore, M16×1.5 female, left-hand

  • Eye bore16 mm
  • ThreadM16×1.5 female
  • HandLeft-hand
  • LinerPTFE
[PLACEHOLDER]
Rod end, 20 mm bore, M20×1.5 male, greasable — placeholder illustration

Rod end, 20 mm bore, M20×1.5 male, greasable

  • Eye bore20 mm
  • ThreadM20×1.5 male
  • LubricationGrease nipple
  • SealSealed
[PLACEHOLDER]

Eccentric Bearings

Back to top of this page

An eccentric bearing has a bore that is deliberately offset from the outside diameter, so rotating the bearing or its sleeve moves the shaft centre by a controlled amount. That offset is used to set a nip, take up a chain or belt, adjust a roller gap, or convert rotation into a small reciprocating stroke. It is a compact way to build an adjustment into a machine without a sliding bracket or a threaded tensioner: printing press impression rollers, vibrating screens, conveyor take-ups, textile rollers, packaging machine drives and eccentric pumps all use the principle. Because the offset creates an unbalanced mass, the bearing is a drive component as well as a support, and its balance and locking arrangement matter as much as its load rating.

The first value to send is the eccentricity — the distance between the bore centre and the outer-ring centre — followed by bore, outside diameter and width. State whether the offset is ground into the inner ring, produced by an eccentric sleeve, or built into the outer ring, and how the setting is locked: a set screw, a key, a clamping collar or a tapered sleeve. Give the radial and axial loads, the rotational speed, the required adjustment range and whether the setting is made once at assembly or changed while the machine runs. Ask about the balancing grade if the shaft runs fast, since an unbalanced eccentric will shake the whole frame and shorten the life of every bearing nearby. Include the mating shaft and housing tolerances and the lubrication path; an eccentric sleeve often needs its own grease supply. We supply the bearing and sleeve as a matched set from the partner factory with the measured eccentricity on the inspection record, so the adjustment you set on the bench is the one you get on the machine.

Eccentric bearing, 25 mm bore, 1.0 mm offset, lock collar — placeholder illustration

Eccentric bearing, 25 mm bore, 1.0 mm offset, lock collar

  • Bore25 mm
  • Eccentricity1.0 mm
  • LockingLock collar
[PLACEHOLDER]
Eccentric bearing, 35 mm bore, 1.5 mm offset, eccentric sleeve — placeholder illustration

Eccentric bearing, 35 mm bore, 1.5 mm offset, eccentric sleeve

  • Bore35 mm
  • Eccentricity1.5 mm
  • LockingTapered sleeve
[PLACEHOLDER]
Eccentric bearing, 45 mm bore, 2.0 mm offset, sealed — placeholder illustration

Eccentric bearing, 45 mm bore, 2.0 mm offset, sealed

  • Bore45 mm
  • Eccentricity2.0 mm
  • Seal2RS
[PLACEHOLDER]

Send the Assembly, Not Just the Bore

For these five families the drawing is the shortest route to a correct quote. If you do not have one, give the mating part number, the flange or thread dimensions, the load and speed, and the one value that makes the part special: the bolt circle for a hub unit, the breakdown voltage for an insulated bearing, the contact angle and preload for a screw support, the thread hand for a rod end, or the offset for an eccentric. Add the quantity and the Incoterm and we will come back with MOQ, lead time and any tooling cost up front.

Request a Quote for Special & Automotive Bearings

Send the dimensions, the quantity and the destination port in one RFQ. We reply with price, MOQ, lead time and Incoterms.