Thrust tapered roller bearing, 50 × 110 × 32 mm
- Shaft washer bore50 mm
- Housing washer OD110 mm
- Assembly height32 mm
- DirectionSingle
Roller bearings replace the balls with cylindrical, tapered, needle or barrel-shaped rollers, so the rolling element meets the raceway along a line rather than at a point. Line contact spreads the load over more material, which is why a roller bearing of the same bore carries substantially more radial load than a ball bearing — at the cost of a lower speed ceiling and more sensitivity to misalignment. The seven families below differ in roller shape, whether axial load can be accepted alongside the radial load, and how the bearing is located on the shaft. We source all seven from audited partner factories and ship them with a dimensional inspection report and material certificate tied to the lot, so a mixed roller and ball part list can travel as one consignment.
One technical point worth stating plainly: a spherical roller bearing is an independent roller bearing family with barrel-shaped rollers running on a spherical outer raceway. It is not a variant of a deep groove ball bearing, and it is not the same part as a spherical ball (insert) bearing. If a drawing or an old supplier list uses loose wording, send us the designation and the dimensions — we cross-reference by size and roller form, not by a name that may have been translated badly.
A thrust tapered roller bearing uses conical rollers whose apex lines converge on the bearing axis, arranged between two flat washers. The geometry gives pure rolling along the roller length under axial load and a very high axial stiffness, so the bearing takes heavy thrust with little axial deflection. It does not accept radial load, and it is normally used where a large axial force must be reacted in a compact axial envelope: rolling mill screw-down mechanisms, crane and hoist hooks, large gearbox thrust locations, extruders, and oil-drilling or pile-driving equipment. Some versions are supplied with a spherical housing washer to absorb small static alignment errors in the supporting structure.
Specify the axial load in both running and static conditions, the shaft washer bore and housing washer outside diameter, the assembly height, and whether the thrust reverses — a reversing load needs a different arrangement, often two opposed bearings. Speed matters because these are moderate-speed components: give the rotational speed and the lubrication method, and state whether oil circulation or grease is available, since heat removal often sets the limit. Include the minimum axial load if the assembly can run unloaded, because a thrust roller bearing needs a preload to keep the rollers from skewing. Tell us the mounting surface hardness and flatness too; a soft or uneven seat will brinell the washers regardless of the bearing rating. We quote the bearing together with any seating washers as one line item.
Needle roller bearings use rollers that are long relative to their diameter — typically three to ten times — which gives a high radial load capacity inside a very small radial section. Where a ball bearing would need a tall ring stack, a needle bearing fits into the same envelope as a plain bush but with rolling instead of sliding friction. That is why they sit in gearbox layshafts, connecting rod small ends, universal joints, cam followers, printing and textile machinery, and hydraulic pumps. They are supplied as drawn-cup types with a thin hardened outer shell, as machined-ring types with inner rings, as cage-and-roller assemblies with no rings at all, or as track rollers with a stud.
The decisive question is whether there is an inner ring. If your design runs the rollers directly on the shaft, the shaft journal becomes the inner raceway and must be hardened to roughly 58–62 HRC, ground to the right finish and held to a tight tolerance — we will ask for that value before quoting, because a soft journal destroys the bearing in hours. Give the shaft diameter, outer diameter or housing bore, width, the radial load and the speed, and say whether axial location is needed (a needle bearing without flanges takes radial load only). State the cage material, the lubrication path and whether the application sees oscillation rather than continuous rotation, since oscillation changes the load rating. If you have no hardened shaft, we will quote a version with an inner ring instead of letting the assembly run on an unprepared surface.
A crossed roller bearing arranges cylindrical rollers at right angles to one another in alternating orientations within a single raceway, usually separated by a cage or spacer. Because half the rollers react load in one plane and half in the perpendicular plane, one compact bearing carries radial load, axial load in both directions and overturning moment at the same time — a job that otherwise needs two bearings spaced apart on a shaft. Rigidity is high and the assembly stays thin, which is why these bearings are used in robot wrist joints, precision rotary tables, indexing heads, medical imaging gantries, radar antennas and optical alignment stages.
Selection is driven by moment stiffness rather than by a simple dynamic load rating. Give the axial and radial loads, the overturning moment, the required angular accuracy and the allowable deflection under load, and we will confirm the size and the preload class. State whether you need an integrated inner/outer ring type or a split outer ring that can be adjusted on assembly, the mounting face flatness and the bolt-hole pattern, the seal arrangement and the lubrication interval. Precision grades for rotary-table duty are tighter than for general automation, so tell us the grade if the drawing specifies one. Crossed roller bearings are sensitive to mounting surface errors: include the flatness and perpendicularity of the two seats in the RFQ, and we will flag any value that cannot hold the accuracy you are asking for.
Turntable bearings, also called slewing rings, are large-diameter bearings designed to connect a rotating upper structure to a fixed base while carrying axial load, radial load and a large overturning moment at the same time. They use either a four-point-contact ball raceway or crossed rollers, and one ring is often cut with internal, external or no gear teeth so the drive pinion can turn the assembly directly. Typical installations are excavator and crane slewing platforms, wind turbine yaw and pitch drives, solar trackers, radar pedestals, aerial work platforms and rotary material handling tables. The bearing is a structural component, not just a spare part: its bolted interface determines stiffness and fatigue life.
The values to send are the axial load, radial load and overturning moment (with the load case and duty cycle if it is cyclic), the required gear data — internal or external teeth, module, tooth count and any heat treatment — the mounting hole circle and bolt quantity, and the required rotational accuracy and backlash. State the sealing and re-lubrication arrangement, the environment (outdoor, marine, dust, temperature range) and the expected service life, since these decide the raceway hardening and the grease channels. Bolt preload and the flatness of the two mounting structures are part of the specification, not an afterthought; include them if they are fixed. We supply the ring with the gear data, inspection record and a bolt-tightening sequence from the partner factory, and we will confirm whether the moment load fits the proposed section before quoting.
A roller bearing RFQ needs the load direction as well as the size. State radial load, axial load (one way or reversing), speed and misalignment, then which bearing is the locating position and which is free to float. Add clearance, cage preference and lubrication. If you only have the marking from an old part, send it with bore, outside diameter and width — we cross-reference by dimensions and roller form, and we will flag any drawing whose family name does not match its geometry rather than quietly quote the wrong bearing.
Send the dimensions, the quantity and the destination port in one RFQ. We reply with price, MOQ, lead time and Incoterms.